Massive Tone For The Masses
The Microtubes 500 is a 500W amplifier equipped with an all analog solid state preamplifier and a Class D Power Module.
On the top row, you will find the clean section which is the foundation of your tone. It features a Gain control and an active 4 band EQ: along with Low and Treble controls, you will find Low Mids and Hi Mids controls, each knob with their own 2-way frequency switch.
On the bottom row, you will find the Microtubes Engine, an extra channel that will bring your clean tone to the next level by helping you cut through the mix while adding anything from subtle, tube-like, harmonics and natural compression to obliterating distortion.
•Dual Microtubes Engine: powered by B3K and VMT (foot switch not included).
•Gain and Master controls for Clean channel.
•4 Band Active Equalizer.
•Two-way Mid Frequency switches for Lo and Hi Mid controls.
•Direct Output (Unaffected by Master Volume).
•Effects Loop (Unaffected by Master Volume).
•Input: Connect your instrument via a standard ¼” mono cable.
•Passive/Active: Switch from passive to active mode. Some active basses can have a hotter signal output which can make the amp distort early (feel free to use it on Passive move even with active basses if such additional distortion is desired).
•Microtubes: Turns on or off the Microtubes Engine to add natural compression, organic harmonic enhancement, and saturation ranging from mild overdrive to high gain bass rage. The Microtubes Engine operates before the clean section (you can therefore use the 4 Band Active EQ for additional tone shaping in addition to the Tone knob described below).
•Drive: Controls the amount of distortion that the Microtubes Engine will deliver. It will change from a soft warm overdrive to a massive modern distorted tone.
•Tone: Controls the high harmonic content of the Microtubes Engine via a variable low pass filter: crank it up for additional attack and definition or dim it down for a smoother sound. This is handy if running bright clean EQ settings or cabinets with tweeters.
•Level: Controls the Microtubes Engine’s output volume.
•Blend: Mixes between the Clean signal and the Distortion signal (Microtubes Engine).
•B3K/VMT: Selects between two overdrive voicings: B3K mode will deliver an aggressive, percussive sound while the VMT will bring up the mids for a warmer, more neutral character.
•Gain: Changes the volume of the signal the Active 4 Band EQ. You can set it low prior to ensuring the cleanest operation possible or set it higher for more aggressive growl.
•Bass: +-12dB at 80Hz. Changes the low content of the signal.
•Low Mids: +-12dB of the selected frequency via the LOW MIDS ƒ switch (described below). Changes the lower mid content of the signal.
•Low Mids ƒ: Use this switch to change the frequency of the low mid band from 250Hz, 500Hz or 1kHZ.
•Hi Mids: +-12dB of the selected frequency via the HI MIDS ƒ switch (described below). Changes the higher mid content of the signal.
•Hi Mids ƒ: Use this switch to change the frequency of the hi mid band from 750Hz, 1.5kHz and 3kHZ.
•Treble: +-12dB at 5kHz. Changes the high content of the signal.
•Master: Controls the overall volume of the amplifier.
•Mute: Mutes the amplifier.
•Speaker Output: Connects the amplifier to your cabinet. This Speakon combo jack allows for either Speakon or ¼” speaker cable operation.
•Min-Load: Press when using a 2Ω load. You can use this control to lower the output if your 4Ω cabinet is not able to handle more than 500W (you can also get 350W with an 8Ω cabinet in this configuration).
•Pre Amp Out: This output connects the preamp to a different power amp.
•Power Amp In: Use this input to connect a different preamp to the power amp. (master volume will be disabled)
•Post-Pre: Selects what signal will be delivered by the DI output. Selecting PRE, sends a clean copy of your input bass signal. Selecting POST delivers a signal processed by the preamp of the amp (gain, distortion, eq, master, etc.)
•Ground Lift: Lifts the ground of the DI XLR output. If a ground noise in you DI signal is experienced, try changing the setting of this control.
•Balanced Output: Connects the Microtubes 900™ preamplifier to balanced equipment (mic preamp, console, recorder, compressor, audio interface, etc.) via a standard XLR jack.
•Footswitch: The Footswitch allows you to remotely engage and disengage the Microtubes Engine. Hold the footswitch to Mute the amplifier. The VMT/B3K push button will remain operational with the Intelligent Footswitch plugged in.
•AC Socket: Connects the power cord to the amplifier.
•AC Power ON/OFF: Turns the amplifier on or off.
For more information feel free to visit http://www.darkglass.com/